NSW Test and Tag Requirements and FAQs
Test and tag rules can sound more mysterious than they need to. For most workplaces, the starting point is simple: know what equipment is being used, where it is being used and whether it is exposed to damage.
Newcastle Test and Tag provides appliance testing and tagging for local workplaces, with RCD testing available where safety switches also need checking.
- AS/NZS 3760
- SafeWork NSW
- Portable equipment
- Testing records
What AS/NZS 3760:2022 Covers
AS/NZS 3760:2022 deals with in-service inspection and testing of electrical equipment. In plain English, that means checking portable equipment that is already being used in a workplace.
The standard is about inspection, electrical testing, tagging and records. It does not turn every item into the same risk. A tool used on a construction site is not in the same setting as a monitor sitting on an office desk.
A compliant electrical test covers a few different elements. Here’s what we’ll provide:
- Visual Inspection: Plug casing, cord clamping, insulation wear, socket condition.
Earth Continuity: Proving protective earth resistance is below 1 Ohm. - Insulation Resistance: 500V D
- C testing to verify internal insulation integrity (or 250V for surge-protected equipment).
- Polarity Check: Verifying active, neutral, and earth wiring on cord sets.
How Workplace Conditions Affect Testing
SafeWork NSW guidance explains that inspection and testing frequency depends on the type of equipment and the conditions where it is used. Equipment exposed to movement, moisture, dust, heat or physical damage needs closer attention than equipment in a low-risk area.
That is why Newcastle Test and Tag asks about the workplace before quoting. A workshop, construction site, staff kitchen and shared office all create different access and testing issues.
Our testing-frequency guide explains how equipment use and workplace conditions affect the next testing date.
Construction Sites and Higher-Risk Workplaces
Construction and demolition sites have stricter expectations for portable electrical equipment and leads. The equipment is moved, handled, dragged, stored and exposed to tougher conditions than most office gear.
For construction test and tag, make tools, chargers, extension leads and site-shed equipment available together where possible. If a principal contractor needs a record by a certain date, raise it before the visit.
AS/NZS 3760:2022 Retesting Intervals
| Workplace Environment | Retest Frequency | Reference Standard |
| Construction & Demolition | 3 Months | AS/NZS 3012 |
| Workshops, Manufacturing & Warehousing | 6 Months | AS/NZS 3760:2022 |
| Commercial Cleaning Equipment | 6 Months | AS/NZS 3760:2022 |
| Offices & General Workplaces (Equipment with flexible cords) | 12 Months | AS/NZS 3760:2022 |
| Fixed Equipment / Low-Risk Areas (Rarely flexed or moved) | Up to 5 Years | AS/NZS 3760:2022 |
Tags, Records and Failed Items
A test tag shows that an item was tested at a point in time. The record gives the workplace a clearer view of what was checked and what result was recorded.
A current tag does not mean equipment can never become unsafe. If a lead is crushed, a plug is cracked or a casing is damaged after testing, the item should be taken out of use.
RCD Testing Is Different
RCD testing checks safety switches, not portable appliances. It may be booked with appliance testing and tagging, but the records should show the services separately.
Switchboard access and power interruption need to be planned before RCD testing. This matters in offices, tenanted buildings, workshops and sites with equipment that cannot be turned off without notice.
Frequently asked questions
Is there one test and tag interval for every workplace?
No. The interval depends on the equipment and the environment where it is used. Construction, workshop and low-risk office equipment can have different expectations.
Who can test and tag electrical equipment?
Testing should be done by a competent person. The person needs the knowledge and equipment to inspect, test, tag and record the result properly.
Does a current tag mean the equipment is always safe?
No. Equipment can be damaged after testing. If a lead, plug or casing looks unsafe, take it out of use even if the tag date has not expired.
Does appliance testing include the building wiring?
No. Appliance testing covers portable electrical equipment. Fixed wiring and installation work need the correct electrical pathway.
Is RCD testing part of appliance testing?
No. RCD testing checks the safety switch rather than the appliance. Keep the quote and records clear when both services are booked.
Where can I check NSW guidance?
SafeWork NSW publishes guidance on electrical inspection and testing and RCDs. Newcastle Test and Tag can provide the testing service, but workplace obligations remain site-specific.